Welcome to the mechanical, mathematical, and customer service quiz.
Please enter your information below to begin the 25 question quiz.
First Name
*
Last Name
*
Phone
*
Email
*
A tape shows a mark exactly halfway between 5 3/4" and 6". What is the measurement?
*
5 7/8"
5 13/16"
5 15/16"
5 5/8"
Which measurement is LONGER?
*
11 5/8"
11 9/16"
They are equal
Cannot determine
Convert 3/16" to a decimal (closest).
*
0.125
0.187
0.250
0.375
An order calls for 24 3/4" ± 1/8". What is the MINIMUM acceptable length?
*
24 1/2"
24 5/8"
24 3/4"
24 7/8"
A hose is ordered at 9' 6". How many total inches is that?
*
108
112
114
120
Why does adding a second adapter increase system risk?
*
Increases pressure
Adds another potential leak point
Reduces flow automatically
Improves strength
A hose twists slightly while tightening the fitting. What is the MAIN concern?
*
Cosmetic damage
Internal reinforcement stress
Reduced sealing
Pressure drop
Which change MOST increases torque when loosening a tight fitting?
*
Pull faster
Use a longer wrench
Change hand angle
Add thread sealant
A conveyor belt consistently tracks to one side. What is the MOST likely cause?
*
Electrical issue
Uneven tension or misalignment
Incorrect belt material
Motor overheating
A fitting seals using a flare, but you connect it to a tapered thread port. What should you do?
*
Add more tape
Verify sealing compatibility before installing
Tighten harder
Use sealant instead
Customer needs 1" Male JIC to 3/4" FPT. You have: 1" Female JIC → 3/4" Male NPT 3/4" Female NPT → 3/4" FPT What should you do?
*
Combine them and verify ratings and sealing
Refuse the order
Use only the first fitting
Guess and build
You find a workaround, but one part is rated below the system pressure. What is the BEST response?
*
Install it anyway
Inform the customer and find a properly rated solution
Use it temporarily
Ship it and warn them
A custom hose fits, but routing forces a bend tighter than spec. What should you do?
*
Deliver it
Adjust length or fitting orientation
Ignore the bend
Reduce pressure rating
A coworker picked a fitting that “almost matches.” What is the BEST action?
Let it go
Verify specs together
Fix it quietly
Change paperwork
A rush order is complete. What is the FINAL step before release?
Print invoice
Double-check threads, length, and pressure rating
Ask customer to test
Ship immediately
Inventory count is short by one item during receiving. What should you do FIRST?
Adjust system
Document and report discrepancy
Ignore it
Pull from another bin
The same SKU is repeatedly picked wrong. What is the BEST long-term fix?
Keep correcting it
Improve bin labeling/location
Move it randomly
Tell shipping
Why must custom solutions be documented on the order?
For billing only
For reorders, troubleshooting, and accountability
For appearance
It doesn’t matter
Which forklift practice is SAFEST while moving?
Load high
Forks low
Turn fast
Carry unstable load
If a load exceeds safe lifting limits, what is the BEST response?
Lift anyway
Ask for help or equipment
Avoid task
Break rules
Hose costs $15/ft. Length is 8' 4". Total cost?
$120.00
$125.00
$130.00
$135.00
A sheet is 12" × 36". How many 6" × 6" squares fit?
8
10
12
14
Which is GREATER?
0.625
5/8
They are equal
Cannot determine an option
A gasket OD is 14", ID is 10". What is the sealing width?
1"
2"
3"
4"
You measure 47 7/8". The order calls for 48" ± 1/8". What should you do?
Ship it
Adjust to hit target spec
Change paperwork
Ask later